Company introduction :Jiangsu Xingxing Drying Equipment Co., Ltd
DESCRIPTION
Fluidized drying, also known as fluidized bed, consists of air filter, heater, fluidized bed, cyclone separator, bag-type dust collector, high-pressure centrifugal fan and operation table. Due to the different nature of the dried materials, equipped dedusters may be considered according to different needs: you can choose both of cyclone separator, bag-type dust collector or either one of them. Generally, heavier materials such as electuary and pellets drying simply need the cyclone separator, while lighter granular and powdered materials require bag-type dust collector, with pneumatic feeding device and belt conveyor for selection. Loose granular solid materials feed into fluidized bed dryer from the feeder. After heated, clean filtered air is sent into the bottom of fluidized bed by the blower, and contact with the solid material via distribution plate to form fluidization and achieve gas-solid heat and mass transfer. After being dried, the materials are discharged from the discharge port; exhaust gases are discharged from the top of the fluidized bed, and are evacuated after solid powder is recovered from them by cyclone separator and bag-type dust collector.
Steam, electricity, hot air furnace can be used (as request).
WORKING PRINCIPLE
Clean hot air goes into the bed distributed through valve plate; wet materials from feeder go into boiling under hot wind. The wide contact between hot air and the materials enhanced heat and mass transfer process so it can be dried in a relatively short period of time. If continuously, materials enter from one end of the bed and, after fluidized drying for tens seconds to a few minutes, automatically flows out from the other end of the bed. This equipment is generally operated at negative pressure.
APPLICABLE MATERIALS
Drying operation of medicines, chemical raw materials, food, food processing and forage. Such as: drying raw material medicine, tablet granules, electuary of Chinese medicine, health food, beverage powder, corn germ, forage, Plastic resin, citric acid and other powder materials. Particle size of applicable materials is generally 0.1 ~ 6mm, and the optimum size is 0.5 ~ 3mm.
PARAMETER
Note:1.The feeding way has:1>.star feeding 2>.combining star feeding air conveyor 3>.belt conveying 4>.decided by customer
2. Automatic production can be realized.3.Besides the model above mentioned,the special model can also be designed and manufactured as request.4.According different raw material,the power of fan will be differ.
CERTIFICATE
We Invite customers to visit our company and communicate on technical requirements face to face.
sale service
Responsible for debugging the equipment according to customers' requirements of various technical data. Our engineers will train our customers about equipment features and operation key points to make sure the equipment running in the best condition.
after-sale service
We provide installation, debugging, maintenance, training and other services; Provide relevant technical data, equipment, software and related GMP certification materials;Set up after-sales service hotline, and arrange personnel to visit customers every year to know more customer needs,like customer operation problems in the process of production equipment.
quality promise
Our company promises strictly operate the ISO9001 quality system certification standards and pharmaceutical equipment GMP audit requirements,promise we provide new equipment. Advanced technology,good quality.Equipment operation safe reliable, affordable, easy to maintain.
Equipment warranty period is one year,all the parts for the equipment choose well-known brand.
During the warranty when equipment have problem in quality like equipment failure and damage,the company for free maintenance or replacement.
We look forward to cooperating with partners from all over the world to build win-win
cooperation relationship in long term. Welcome for your visiting.
DESCRIPTION
Fluidized drying, also known as fluidized bed, consists of air filter, heater, fluidized bed, cyclone separator, bag-type dust collector, high-pressure centrifugal fan and operation table. Due to the different nature of the dried materials, equipped dedusters may be considered according to different needs: you can choose both of cyclone separator, bag-type dust collector or either one of them. Generally, heavier materials such as electuary and pellets drying simply need the cyclone separator, while lighter granular and powdered materials require bag-type dust collector, with pneumatic feeding device and belt conveyor for selection. Loose granular solid materials feed into fluidized bed dryer from the feeder. After heated, clean filtered air is sent into the bottom of fluidized bed by the blower, and contact with the solid material via distribution plate to form fluidization and achieve gas-solid heat and mass transfer. After being dried, the materials are discharged from the discharge port; exhaust gases are discharged from the top of the fluidized bed, and are evacuated after solid powder is recovered from them by cyclone separator and bag-type dust collector.
Steam, electricity, hot air furnace can be used (as request).
WORKING PRINCIPLE
Clean hot air goes into the bed distributed through valve plate; wet materials from feeder go into boiling under hot wind. The wide contact between hot air and the materials enhanced heat and mass transfer process so it can be dried in a relatively short period of time. If continuously, materials enter from one end of the bed and, after fluidized drying for tens seconds to a few minutes, automatically flows out from the other end of the bed. This equipment is generally operated at negative pressure.
APPLICABLE MATERIALS
Drying operation of medicines, chemical raw materials, food, food processing and forage. Such as: drying raw material medicine, tablet granules, electuary of Chinese medicine, health food, beverage powder, corn germ, forage, Plastic resin, citric acid and other powder materials. Particle size of applicable materials is generally 0.1 ~ 6mm, and the optimum size is 0.5 ~ 3mm.
PARAMETER
| Model and specifications Technical Parameters | XF0.25-1 (Original XF10) | XF0.25-2 (Original XF20) | XF0.25-3 (Original XF30) | XF0.25-6 | XF0.3-2 | XF0.3-4 | XF0.3-6 | XF0.3-8 | XF0.3-10 | XF0.4-4 | XF0.4-6 |
| Area of bed layer(m2) | 0.25 | 0.5 | 1.0 | 1.5 | 0.6 | 1.2 | 1.8 | 2.4 | 3.0 | 1.6 | 2.4 |
| Drying capacity(kg h2O/h) | 10-15 | 20-25 | 30-45 | 52-75 | -30 | 42-60 | 63-90 | 84-120 | 105-150 | 56-80 | 84 |
| Power of fan(kw) | 5.5 | 7.5 | 15 | 22 | 7.5 | 18.5 | 30 | 37 | 48 | 30 | 37 |
| Temperature of air in(oC) | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 |
| Temperature of air in(oC) | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 |
| Overall dimensions(main machine) L×W×H(m) | 1×0.6 ×3.35 | 2×0.6 ×3.35 | 4×0.6 ×3.35 | 6×0.6 ×3.35 | 2×0.70 ×3.4 | 4×0.7 ×3.4 | 6×0.7 ×3.4 | 8×0.7 ×3.4 | 10×0.7 ×3.4 | 4×1 ×3.58 | 6×1 ×3.58 |
| Occupied area(m2) | 18 | 25 | 35 | 40 | 25 | 38 | 45 | 56 | 70 | 18 | 56 |
| Model and specifications Technical Parameters | XF0.4-8 | XF0.4-10 | XF0.4-12 | XF0.5-4 (Original XF50) | XF0.5-6 | XF0.5-8 | XF0.5-10 | XF0.5-12 | XF0.5-14 | XF0.5-16 | XF0.5-18 |
| Area of bed layer(m2) | 3.2 | 4.0 | 4.8 | 2.0 | 3.0 | 4.0 | 5.0 | 6.0 | 7.0 | 8.0 | 9.0 |
| Drying capacity(kg h2O/h) | 112-160 | 140-200 | 168-240 | 70-100 | 140-200 | 140-200 | 175-250 | 210-300 | 245-350 | 280-400 | 315-450 |
| Power of fan(kw) | 44 | 66 | 66 | 30 | 66 | 66 | 90 | 90 | 150 | 150 | 165 |
| Temperature of air in(oC) | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 | 120-140 |
| Temperature of air in(oC) | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 | 40-60 |
| Overall dimensions(main machine) L×W×H(m) | 8×1 ×3.58 | 10×1 ×3.58 | 12×1.2 ×4.1 | 4×1.2 ×4.1 | 8×1.2 ×4.1 | 8×1.2 ×4.1 | 10×1.2 ×4.1 | 12×1.2 ×4.1 | 14×1.2 ×4.1 | 16×1.2 ×4.1 | 18×1.2 ×4.1 |
| Occupied area(m2) | 74 | 82 | 96 | 50 | 70 | 82 | 100 | 140 | 180 | 225 | 268 |
2. Automatic production can be realized.3.Besides the model above mentioned,the special model can also be designed and manufactured as request.4.According different raw material,the power of fan will be differ.
CERTIFICATE
We Invite customers to visit our company and communicate on technical requirements face to face.
sale service
Responsible for debugging the equipment according to customers' requirements of various technical data. Our engineers will train our customers about equipment features and operation key points to make sure the equipment running in the best condition.
after-sale service
We provide installation, debugging, maintenance, training and other services; Provide relevant technical data, equipment, software and related GMP certification materials;Set up after-sales service hotline, and arrange personnel to visit customers every year to know more customer needs,like customer operation problems in the process of production equipment.
quality promise
Our company promises strictly operate the ISO9001 quality system certification standards and pharmaceutical equipment GMP audit requirements,promise we provide new equipment. Advanced technology,good quality.Equipment operation safe reliable, affordable, easy to maintain.
Equipment warranty period is one year,all the parts for the equipment choose well-known brand.
During the warranty when equipment have problem in quality like equipment failure and damage,the company for free maintenance or replacement.
We look forward to cooperating with partners from all over the world to build win-win
cooperation relationship in long term. Welcome for your visiting.
China
